If a new component would be installed, there are procedures for that which you need to bear in mind. The procedures have to be followed to install Profile Design Cobra bars properly. That is also a requirement on the policy for the warranty that is provided when you buy one. When you are now knowledgeable on such task, go to its dealer near the area.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
They have a manual which contains all of the steps you must do. If you will just do that on your own, you should prepare all of the tools that are needed for this. You must have an Allen or torque wrench. You must also have some sandpaper as you are going to use that to make it smoother. If you have all of what you needed then you could now start on that.
You have to avoid putting grease on its clamping area. When you will grease that, it will be causing that bar to slide from its place. You should be certain that a situation like that will not be happening specifically when you would use the bike. You will surely lose control as you would ride your bike. When it will be happening, it would be risky for you.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
When you have a new stem installed, you should also read the instructions of the manufacturer. There are also methods which the manufacturer has set so you could make sure that it would be done correctly. They would indicate that in the manual that they would provide to you so you would not have a hard time on how you would be doing it.
You have to look on a front stem clamp to see if there are sharp edges on it. Use some sandpaper so you will be able to remove it. This should be done so the fiber from the aluminum or the carbon will not be damaged. Once it is already on its place, you can immediately clamp that to a stem. You should be certain that it has been tightened.
You should slide the lever to the bar. If it makes you uncomfortable, you should adjust it depending on what you want. You have to place it carefully. You have to remember that if it would be broken, it would affect the warranty of the material.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
Following the right procedures is really necessary. That would be dangerous for somebody if he will be losing control of his bike. Major injuries might be acquired from it.
About the Author:
You can visit www.sportfactoryproshop.com for more helpful information about Procedures On Installing Profile Design Cobra Bars You Must Follow.
0 commentaires:
Enregistrer un commentaire