Although it is true that custom made arch support insoles for those who have flat feet must be made by a licensed professional, it is actually possible to make handmade orthotics at home. However, these types should only be made for those whose flat foot condition is not too severe. Basically, the homemade ones can be made for those who have low arches in order to stay safe.
Now before one would want to make one of these things, he would first have to get hand of certain materials. Now the most important thing that he would need would be some insoles probably from other shoes that he does not use anymore. Just make sure that all sizes of these things are more or less the same or similar.
Once these soles have already been gotten, then the very next thing to do would be to get some glue. One is recommended to use super glue for this kind of project because super glue is very efficient and dries fast. However, if one does not have super glue in his house, then he may use some other sticky glue that is waterproof.
Now the first thing to do would be to get the existing insoles and measure them. As stated earlier, all of the insoles have to be of the same size so that there will be consistency. After that, put one insole on top of another and determine which part is the part that would hold the arch.
After determining the part that would hold the arch, then he now has to cut that part with the sharp scissors. Now he has to make sure that the part that was cut out is really able to fit the insole that is whole otherwise one would have to cut it a little bit more. Once he has already done that, then the next part would be to now glue that small part to the whole insole.
Now when that is already done, then all that is left to do is wait for the glue to dry. If the glue takes a bit long to dry, then he may put the sole in front of an electric fan so that it will dry faster. However, if one uses super glue, then the glue will be able to dry in just a few minutes.
Now if one notices that the arch support is not high enough, then he may actually add another layer if he would want to. All he has to do is get another insole and just repeat the process that was done a while ago. After that, he just has to wait for the glue to dry again and try it on.
Now if one is an athlete who needs a higher arch support or is a person who has a low arch, then he may actually make handmade orthotics at home to save money. Now if he has a very severe case of being flat footed, then it is best that he already buys a custom made one. Other than that, the handmade one is actually more than enough.
Now before one would want to make one of these things, he would first have to get hand of certain materials. Now the most important thing that he would need would be some insoles probably from other shoes that he does not use anymore. Just make sure that all sizes of these things are more or less the same or similar.
Once these soles have already been gotten, then the very next thing to do would be to get some glue. One is recommended to use super glue for this kind of project because super glue is very efficient and dries fast. However, if one does not have super glue in his house, then he may use some other sticky glue that is waterproof.
Now the first thing to do would be to get the existing insoles and measure them. As stated earlier, all of the insoles have to be of the same size so that there will be consistency. After that, put one insole on top of another and determine which part is the part that would hold the arch.
After determining the part that would hold the arch, then he now has to cut that part with the sharp scissors. Now he has to make sure that the part that was cut out is really able to fit the insole that is whole otherwise one would have to cut it a little bit more. Once he has already done that, then the next part would be to now glue that small part to the whole insole.
Now when that is already done, then all that is left to do is wait for the glue to dry. If the glue takes a bit long to dry, then he may put the sole in front of an electric fan so that it will dry faster. However, if one uses super glue, then the glue will be able to dry in just a few minutes.
Now if one notices that the arch support is not high enough, then he may actually add another layer if he would want to. All he has to do is get another insole and just repeat the process that was done a while ago. After that, he just has to wait for the glue to dry again and try it on.
Now if one is an athlete who needs a higher arch support or is a person who has a low arch, then he may actually make handmade orthotics at home to save money. Now if he has a very severe case of being flat footed, then it is best that he already buys a custom made one. Other than that, the handmade one is actually more than enough.
About the Author:
For a summary of the advantages of handmade orthotics don't hesitate to check out our website today. To reach our homepage now, just click on this link http://www.customorthoticfootbeds.com.
0 commentaires:
Enregistrer un commentaire